PIC16F785-I/ML【PDF 37/206 页】IC PIC MCU FLASH 2KX14 20QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3880

33页 34页 35页 36页 [37页]38页 39页 40页 41页

131

8272E–AVR–04/2013

ATmega164A/PA/324A/PA/644A/PA/1284/P

Using the ICRn Register for defining TOP works well when using fixed TOP values. By using

ICRn, the OCRnA Register is free to be used for generating a PWM output on OCnA. However,

if the base PWM frequency is actively changed by changing the TOP value, using the OCRnA as

TOP is clearly a better choice due to its double buffer feature.

In phase and frequency correct PWM mode, the compare units allow generation of PWM wave-

forms on the OCnx pins. Setting the COMnx1:0 bits to two will produce a non-inverted PWM and

an inverted PWM output can be generated by setting the COMnx1:0 to three (See Table 16-4 on

page 134). The actual OCnx value will only be visible on the port pin if the data direction for the

port pin is set as output (DDR_OCnx). The PWM waveform is generated by setting (or clearing)

the OCnx Register at the compare match between OCRnx and TCNTn when the counter incre-

ments, and clearing (or setting) the OCnx Register at compare match between OCRnx and

TCNTn when the counter decrements. The PWM frequency for the output when using phase

and frequency correct PWM can be calculated by the following equation:

The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).

The extreme values for the OCRnx Register represents special cases when generating a PWM

waveform output in the phase correct PWM mode. If the OCRnx is set equal to BOTTOM the

output will be continuously low and if set equal to TOP the output will be set to high for non-

inverted PWM mode. For inverted PWM the output will have the opposite logic values. If OCR1A

is used to define the TOP value (WGM13:0 = 9) and COM1A1:0 = 1, the OC1A output will toggle

with a 50% duty cycle.

16.11 Timer/Counter Timing diagrams

The Timer/Counter is a synchronous design and the timer clock (clk

Tn) is therefore shown as a

clock enable signal in the following figures. The figures include information on when Interrupt

Flags are set, and when the OCRnx Register is updated with the OCRnx buffer value (only for

modes utilizing double buffering). Figure 16-10 shows a timing diagram for the setting of OCFnx.

Figure 16-10. Timer/Counter Timing diagram, setting of OCFnx, no prescaling.

Figure 16-11 shows the same timing data, but with the prescaler enabled.

OCnxPFCPWM

fclk_I/O

2 NTOP

----------------------------

clk

(clk

I/O/1)

OCFnx

clk

I/O

OCRnx

TCNTn

OCRnx Value

OCRnx - 1

OCRnx

OCRnx + 1

OCRnx + 2

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式